Kia Soul: Tire pressure monitoring system (TPMS) / Changing a tire with TPMS
If you have a flat tire, the low Tire Pressure and Position telltales will come
on. In this case, have the system checked by a professional workshop. Kia recommends
to visit an authorized Kia dealer/service partner.
CAUTION
We recommend that you use the sealant approved by Kia.
The sealant on the tire pressure sensor and wheel shall be eleminated when
you replace the tire with a new one.
Each wheel is equipped with a tire pressure sensor mounted inside the tire behind
the valve stem. You must use TPMS specific wheels. Have your tires serviced by a
professional workshop. Kia recommends to visit an authorized Kia dealer/service
partner.
If you drive the vehicle for about 10 minutes at speeds above 25 km/h after replaceing
the low pressure tire with the spare tire, one of the following will happen:
- The TPMS malfunction indicator may blink for approximately 1 minute and
then remain continuously illuminated because the TPMS sensor is not mounted
on the spare wheel. (changed tire equipped with a sensor not in the vehicle)
- The TPMS malfunction indicator will remain continuously illuminated while
driving because the TPMS sensor is not mounted on the spare wheel. (changed
tire equipped with a sensor in the vehicle)
You may not be able to identify a low tire by simply looking at it. Always use
a good quality tire pressure gauge to measure the tire's inflation pressure. Please
note that a tire that is hot (from being driven) will have a higher pressure measurement
than a tire that is cold (from sitting stationary for at least 3 hours and driven
less than 1.6 km (1 mile) during that 3 hour period).
Allow the tire to cool before measuring the inflation pressure. Always be sure
the tire is cold before inflating to the recommended pressure.
A cold tire means the vehicle has been sitting for 3 hours and driven for less
than 1.6 km (1 mile) in that 3 hour period.
CAUTION
We recommend that you use the sealant approved by Kia if your vehicle is equipped
with a Tire Pressure Monitoring System. The liquid sealant can damage the tire pressure
sensors.
WARNING
TPMS
- The TPMS cannot alert you to severe and sudden tire damage caused by
external factors such as nails or road debris.
- If you feel any vehicle instability, immediately take your foot off
the accelerator, apply the brakes gradually and with light force, and slowly
move to a safe position off the road.
WARNING
Protecting TPMS
Tampering with, modifying, or disabling the Tire Pressure Monitoring System
(TPMS) components may interfere with the system's ability to warn the driver of
low tire pressure conditions and/or TPMS malfunctions. Tampering with, modifying,
or disabling the Tire Pressure Monitoring System (TPMS) components may void the
warranty for that portion of the vehicle.
WARNING
For EUROPE
- Do not modify the vehicle, it may interfere with the TPMS function.
- The wheels on the market do not have a TPMS sensor. For your safety,
use parts for replacement from a professional workshop. Kia recommends to visit
an authorized Kia dealer/service partner.
- If you use the wheels on the market, use a TPMS sensor approved by
an authorized Kia dealer. If your vehicle is not equipped with a TPMS sensor
or TPMS does not work properly, you may fail the periodic vehicle inspection
conducted in your country.
❈ All vehicles sold in the EUROPE market during below period must be equipped
with TPMS.
- New model vehicle : Nov. 1, 2012 ~
- Current model vehicle : Nov. 1, 2014~ (Based on vehicle registrations)
The TPMS malfunction indicator will illuminate after it blinks for approximately one minute when there is a problem with the Tire Pressure Monitoring System. In this case, have the system checked by a ...
Jack and tools The jack, jack handle, wheel lug nut wrench are stored in the luggage compartment. Pull up the luggage box cover to reach this equipment. 1. Jack handle 2. Jack 3. Wheel lug nut wrench Jacking ...
Other information:
1. Open the tailgate. 2. Remove the service cover. (Loosen the lamp assembly retaining screws and remove the lamp assembly from the body of the vehicle for back-up lamp) 3. Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on ...
Push the switch to turn the light on or off. • : The lamp will turn on if this button is pressed. • : The lamp will turn on if this button is pressed. CAUTION Vanity mirror lamp Always have the switch in the off position when the vanity mirror lamp is not in use. If the sunvisor is closed without ...